You will need, there are 2 main issues to be dealt with when constructing a playground: preparing a safe playground flooring and gathering needed equipment. The first issue is much too often overlooked, despite the fact that is it doesn’t flooring which plays a deciding role when a baby is falling down. Falls are the main cause of injuries on a 안전놀이터! Grass or natural soil are usually not necessarily sufficient to cushion the impact of a child’s fall.

The device is another factor and here the money should not be spared. Obviously, the prevailing playing equipment can be used if it is in a good condition and routinely maintained. When buying new equipment, one should choose a reliable company whose equipment complies with international safety standards. Producer should inform you which equipment can be installed in a BUILD IT YOURSELF manner, and what needs to be carried out by a professional company.

Calculating toy store area

Let’s start with designating a safe playground area, that must be large enough not only to fit all the equipment, but also to contain the impact area, which is where a child can fall. Do not forget that the impact area is to be free of obstacles. In order to be able to analyze this area, we need to know the critical fall height of the tools. For example , if the maximum height from which a child can crash is 2 m, the ground has to be covered with defensive playground flooring certified to attenuate the impact from only two metres. Moreover, the flooring should reach 1 . 8 e behind the edge of the equipment in question. The formula for you to calculate the impact area is: 2/3*critical fall height and 50cm.

This means that one should always pave the playground using safety flooring reaching 1 . 5 to 2 . your five metres behind the equipment.

Another important safety requirement is that the greatest fall height is 3 metres. So , make sure non-e of the equipment where a child can stand or climb up is higher than 3 m. Finally, let’s not forget with regards to common sense which should guide you in the first place when building a private sports ground.

Preparing the subfloor

Once you have looked at the location of the active equipment or installed the new one (following the manufacturer’s instruction) and once you have designed the total playground area, you need to prepare the subfloor. If you build a DIY playground its much easier if the subfloor is bound (e. g. concrete floor, paving stone, asphalt, tiles). In that case, you can lay essential safety flooring directly on top of it, without the need to prepare the base study course. If you choose rubber playground mats which are interlocking, you will not possibly need to glue the tiles.

If your subfloor is unbound, for example it is soil, sand or grass, you need to get it ready first to make it load-bearing and solid. The best and most inexpensive way is to prepare a grit or gravel bedding. Levels the existing area and place a layer of about 15 cm of sharp-edged gravel, which should be compacted and levelled. Anyone can pave the safety playground mats directly onto the pebbles bedding. Rain water will seep through the porous mats along with through the gravel layer to the ground. This solution is ecological and very practical – there will be no puddles and young children can use the playground in any weather!

Low-maintenance playground floor

Rubber mats are the most practical flooring solution for that safe DIY playground. Apart from the fact that they are childishly straightforward to install, they require practically no maintenance. Playground mats are produced from a permanently elastic material (polyurethane-bonded rubber granulate) which suggests they are absolutely weatherproof. They will not rot or crack, and they will last for about 15 years or more. If there is any problem, specific mats can be lifted or exchanged.

Other playground elements are either very expensive or difficult to maintain. Especially mud, grass or wood chips need constant maintenance, change and replenishment. The expenses related to this can be overwhelming for one community or neighbourhood. Especially that the layer of these unfastened fill materials has to be quite thick to provide the necessary come protection.

With rubber playground mats it is very easy to give you the fall protection necessary on a particular playground. The manufacturer often informs you what the critical fall height for each health and safety mat is, and which one is suitable for installations on unbound subfloor. Rubber granulate mats are easy to cut on web-site and they have small formats to make DIY work a little bit much easier.